 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| MITSUMI AV Switch for I2C BUS Control, 4-input, 3-output and Canal Plus Compatible MM1422, 1423, 1442, 1443 AV Switch for I2C BUS Control, 4-input, 3-output and Canal Plus Compatible Monolithic IC MM1422, 1423, 1442, 1443 Outline These ICs are four-input, three-output AV switches under I2C BUS control with Canal Plus support, intended for use in VCRs and DVD for the European market. There are four models, described below. Audio subsystems are either stereo or monaural; video subsystems either do or do not have a clamping circuit. Features 1. I2C BUS serial control. 2. Internal two-output 75video driver, internal two-output 600 audio driver. 3. Audio mute function through an external pin. 4. Operating power supply voltage 11 to 13 V 5. Models both with and without video subsystem clamp. 6. Models with monaural and stereo audio subsystems. Package SSOP-34A (MM1443XJ) SDIP-32A (MM1443XD) Applications (1)VCRs with Canal Plus Support for the European Market. (2)DVD Series Table Video input clamp MM1422 MM1423 MM1442 MM1443 Stereo Monaural Package SDIP-32A SSOP-34A MITSUMI AV Switch for I2C BUS Control, 4-input, 3-output and Canal Plus Compatible MM1422, 1423, 1442, 1443 Pin Assignment MM1443XJ 34 33 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 SSOP-34A 1 2 3 4 5 6 7 8 9 E1-V VCC2 E2-V VCC1 EXT-V EXT-L BIAS E2-L Mute 10 11 12 13 14 15 16 17 18 E1-L FS EXT-R(N.C.) Port1 E2-R(N.C.) Port2 E1-R(N.C.) NC NC 19 20 21 22 23 24 25 26 27 GND1 TUN-R(N.C.) ROUT3(N.C.) ROUT2(N.C.) ROUT1(N.C.) TUN-L LOUT3 LOUT2 LOUT1 28 29 30 31 32 33 34 TUN-V VOUT3 VOUT2 VOUT1 SDA SCL GND2 MM1443XD 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 SDIP-32A 1 2 3 4 5 6 7 8 E1-V VCC2 E2-V VCC1 EXT-V EXT-L BIAS E2-L 9 10 11 12 13 14 15 16 Mute E1-L FS EXT-R(N.C.) Port1 E2-R(N.C.) Port2 E1-R(N.C.) 17 18 19 20 21 22 23 24 GND1 TUN-R(N.C.) ROUT3(N.C.) ROUT2(N.C.) ROUT1(N.C.) TUN-L LOUT3 LOUT2 25 26 27 28 29 30 31 32 LOUT1 TUN-V VOUT3 VOUT2 VOUT1 SDA SCL GND2 MITSUMI AV Switch for I2C BUS Control, 4-input, 3-output and Canal Plus Compatible MM1422, 1423, 1442, 1443 Block Diagram Stereo type (MM1423, MM1443) Monaural type (MM1422, MM1442) MITSUMI AV Switch for I2C BUS Control, 4-input, 3-output and Canal Plus Compatible MM1422, 1423, 1442, 1443 Introduction of Main Model AV Switch for I2C BUS Control, 4-input, 3-output and Canal Plus Compatible Monolithic IC MM1443 Pin Description Pin No. Pin name 1 3 5 28 E1-V E2-V EXT-V TUN-V Video input pin Functions Equivalent circuit diagram 2 4 13 15 VCC2 VCC1 Port1 Port2 VCC2 is power supply voltage pin for 75 driver Port output pin 6 8 10 12 14 16 20 24 7 EXT-L E2-L E1-L EXT-R E2-R E1-R TUN-R TUN-L BIAS Audio input pin Bias pin MITSUMI AV Switch for I2C BUS Control, 4-input, 3-output and Canal Plus Compatible MM1422, 1423, 1442, 1443 Pin No. Pin name 9 Mute Mute pin Functions Equivalent circuit diagram 19 34 11 GND1 GND2 FS GND2 is a GND pin for 75 driver FS output pin 21 22 25 26 ROUT3 ROUT2 LOUT3 LOUT2 Audio driver output pin 23 27 ROUT1 LOUT1 Audio buffer output pin MITSUMI AV Switch for I2C BUS Control, 4-input, 3-output and Canal Plus Compatible MM1422, 1423, 1442, 1443 Pin No. Pin name 29 30 VOUT3 VOUT2 Functions Video driver output pin Equivalent circuit diagram 31 VOUT1 Video buffer output pin 32 SDA SDA pin 33 SCL SCL pin 17 18 NC MITSUMI AV Switch for I2C BUS Control, 4-input, 3-output and Canal Plus Compatible MM1422, 1423, 1442, 1443 Absolute Maximum Ratings Item Storage temperature Operating temperature Power supply voltage Allowable loss (Ta=25C) Symbol TSTG TOPR VCC max. Pd Ratings -40~+125 -25~+75 15 700 Unit C C V mW Recommend Operating Conditions Item Operating temperature Operating voltage Symbol TOPR VOP Ratings -25~+75 11~13 Unit C V Electrical Characteristics Item Consumption current [FS pin output level] High voltage Middle voltage Low voltage [Crosstalk] VOUT1 VOUT2 VOUT3 LOUT1 LOUT2 LOUT3 ROUT1 ROUT2 ROUT3 [VOUT1] Voltage gain Frequency characteristic Differential gain Differential phase Maximam output level Input pin voltage Output pin voltage [VOUT2, VOUT3] Voltage gain Frequency characteristic Differential gain (Except where noted otherwise, Ta=25C, VCC=12V) Measurement conditions No-signal, no-load FS pin control High selected FS pin control Mid selected FS pin control Low selected Min. Typ. Max. Unit 33.5 40.0 mA 9.5 4.5 11.0 6.0 0.2 12.0 7.0 1.0 V V V Symbol ICC VFSH VFSM VFSL CTV1 CTV2 CTV3 CTL1 CTL2 CTL3 CTR1 CTR2 CTR3 GV1 FV1 DG1 DP1 VOV1 VIV1 VOV1 GV2 GV3 FV2 FV3 DG2 DG3 VIN=1VP-P f=4.43MHz -70 -50 dB VIN=1Vrms f=1kHz -90 -70 dB VIN=1Vrms f=1kHz -90 -70 dB VIN=1VP-P f=100kHz VIN=1VP-P 10MHz/100kHz VIN=1VP-P: staircase APL = 10~90% VIN=1VP-P: staircase APL = 10~90% f = 100kHz, Maximum output at THD < 1.0% No-signal, no-load No-signal, no-load -0.5 -1.0 -3 -3 2.1 2.3 1.0 0 0 0 0 2.8 1.5 +0.5 +1.0 +3 +3 3.3 2.0 dB dB % deg VP-P V V VIN=1VP-P f=100kHz VIN=1VP-P 10MHz/100kHz VIN=1VP-P: staircase APL = 10~ 90% 5.5 -1.0 -3 6.0 0 0 6.5 +1.0 +3 dB dB % MITSUMI AV Switch for I2C BUS Control, 4-input, 3-output and Canal Plus Compatible MM1422, 1423, 1442, 1443 Item Differential phase Maximam output level Input pin voltage Output pin voltage [LOUT1, ROUT1] Symbol DP2 DP3 VOV2 VOV3 VIV2 VIV3 VOV2 VOV3 Measurement conditions VIN=1VP-P: staircase APL = 10~90% f = 100kHz, Maximum output at THD < 1.0% No-signal, no-load No-signal, no-load Min. Typ. Max. Unit -3 4.2 2.3 1.0 2.8 1.5 3.3 2.0 0 +3 deg VP-P V V G1L1 Voltage gain G2L1 Maximam output level Total harmonic distortion Output noise voltage Output offset voltage Input impedance Input pin voltage Output pin voltage [LOUT2, LOUT3, ROUT2, ROUT3] DL1 THDL1 VNL1 VOFL1 ZINL1 VIL1 VOL1 GOL2 GOL3 G2L2 G2L3 G4L2 G4L3 G6L2 G6L3 VL2 VL3 THDL2 THDL3 VNL2 VNL3 VOFL2 VOFL3 ZINL2 ZINL3 VIL2 VIL3 VOL2 VOL3 VIL VIH VOL IIH IIL fSCL VIN=1Vrms f=1kHz -0.5 TUN-L GAIN adjustment at 0dB VIN=0.25Vrms f=1kHz 11.5 TUN-L GAIN adjustment at 12dB VCC = 12V, f = 1kHz Maximum output at THD < 0.5% 3.0 VIN such that VOUT = 1Vrms, f = 1kHz A curve band 20kHz DC step for switching -15 100 No-signal, no-load 5.30 No-signal, no-load 5.30 VIN=1Vrms TUN-L=0dB Output GAIN adjustment at 0dB VIN=1Vrms TUN-L=0dB Output GAIN adjustment at 2dB VIN=1Vrms TUN-L=0dB Output GAIN adjustment at 4dB VIN=1Vrms TUN-L=0dB Output GAIN adjustment at 6dB VCC=12V f=1kHz Maximum output when THD < 0.5% VIN such that VOUT = 1Vrms f=1kHz G=0, 2, 4, 6dB A curve band 20kHz DC step for switching -15 100 No-signal, no-load No-signal, no-load 5.30 5.30 0 12 +0.5 12.5 dB dB 0.03 3 0 150 5.65 5.65 Vrms 0.1 % 50 Vrms 15 mV 200 k 6.00 V 6.00 V -0.5 1.5 3.5 5.5 3.0 0 2 4 6 +0.5 2.5 4.5 6.5 dB dB dB dB Vrms Voltage gain Maximam output level Total harmonic distortion Output noise voltage Output offset voltage Input impedance Input terminal voltage Output terminal voltage [Logic] (refer to next page) Input voltage L Input voltage H Low level output voltage High level input current Low level input current Clock frequency 0.03 20 0 150 5.65 5.65 0.1 50 15 200 6.00 6.00 % Vrms mV k V V I2C logic L level judgment value I2C logic H level judgment value for SDA 3mA inflow for SDA, SCL = 4.5V impressed for SDA, SCL = 0.4V impressed 0.0 3.0 0.0 -10 -10 1.5 5.0 0.4 +10 +10 100 V V V A A kHz MITSUMI AV Switch for I2C BUS Control, 4-input, 3-output and Canal Plus Compatible MM1422, 1423, 1442, 1443 Item Data transfer waiting time SCL start hold time SCL low level hold time SCL high level hold time SCL start setup time SDA data hold time SDA data setup time SCL rise time SCL fall time SCL stop setup time Symbol tBUF tHD : STA tLOW tHIGH tSU : STA tHD : DAT tSU : DAT tR tF tSU : STO Measurement conditions Min. Typ. Max. Unit 4.7 S 4.0 S 4.7 S 4.0 S 4.7 S 200 nS 250 nS 1000 nS 300 nS 4.0 S I2C BUS control signal SDA tBUF tR SCL S t HD:STA t LOW tF P t HD:DAT t HIGH t SU:DAT t SU:STA Sr t SU:STO P I2C BUS SDA SCL S 1 2 3 4 5 6 7 8 A 1 2 3 7 8 A P S : Start Condition P : Stop Condition A : Acknowledge I2C BUS (Inter IC BUS) is an inter bus system developed by Philips Co. It transmits and receives data through 2 (SDA, SCL) lines. Data are transmitted and received in the units of bytes by MSB first from the start condition. [Control registers] Control registers are data sent from the master for determining the switch condition of the MM1422 series. Slave address 1 0 0 1 0 0 0 R/W 0 Control Register 1 b7 b6 b5 b4 b3 b2 b1 b0 Control Register 2 b7 b6 b5 b4 b3 b2 b1 b0 S A A AP Address byte Control data MITSUMI AV Switch for I2C BUS Control, 4-input, 3-output and Canal Plus Compatible MM1422, 1423, 1442, 1443 The data format of the MM1422 series is set as shown in the above figure. Out of the address bytes, first 7 bits are assigned to the slave addresses, while the residual 1 bit is assigned to the R/W bit. Set the R/W bit to 0 when data are used as control registers. Slave address of the MM1422 series is 90H. Each bit of control registers is reset to 0. MM1422 series consists of one address byte and two control data bytes(3 bytes in total). For details of the control contents of control register 1 and 2, refer to the separate table. [Control Register 1] b7 b6 b5 b4 b3 b2 b1 FS CTRL b0 OUT 1 select [Control Register 2] b7 0, 12dB select b6 Port 1 CTRL OUT 2 select OUT 3 select b5 Port 2 CTRL b4 b3 b2 b1 b0 Mute Audio OUT2 gain select Audio OUT3 gain select All data over the limited length (4th and subsequent bytes) are fully neglected. Because of this, the faulty operation that switch changes by the data after the 4th byte doesn't occur. Each audio output can be set to mute by setting MUTE terminal to high. [Status registers] There is no preparation of the status register in MM1422 series. A status register returns all the 1 when is set in the R/W bit. S Slave address 1 0 0 1 0 0 0 R/W 1 A status register b7 b6 b5 b4 b3 b2 b1 b0 NA P Address byte Status data MITSUMI AV Switch for I2C BUS Control, 4-input, 3-output and Canal Plus Compatible MM1422, 1423, 1442, 1443 Switch Control Table [Control register 1] (2nd byte) b7 b6 b5 b4 b3 b2 b1 b0 0 0 1 1 0 1 0 1 0 0 1 1 0 1 0 1 0 0 1 1 0 1 0 1 0 0 1 1 0 1 0 1 V OUT1 A OUT1 MUTE TUNER V OUT2 A OUT2 V OUT3 A OUT3 FS *1 TUNER SCART E1 SCART E1 SCART E2 SCART E2 *1 TUNER EXT IN MUTE TUNER EXT IN SCART E1 SCART E1 *2 EXT IN MUTE EXT IN SCART E2 SCART E2 SCART E2 SCART E2 Low Middle High High Note 1 : Previous choice condition is held. TUNER is chosen at power on. Note 2 : Previous choice condition is held. EXT IN is chosen at power on. [Control register 2] (3rd byte) b7 b6 b5 b4 b3 b2 b1 b0 0 1 0 1 0 1 0 0 1 1 0 1 0 1 0 0 1 1 0 1 0 1 0 1 0, 12dB 0dB 12dB Low High Low High 0dB 2dB 4dB 6dB 0dB 2dB 4dB 6dB OFF ON Port 1 Port 2 GainOUT2 GainOUT3 MUTE MITSUMI AV Switch for I2C BUS Control, 4-input, 3-output and Canal Plus Compatible MM1422, 1423, 1442, 1443 Measuring Circuit MITSUMI AV Switch for I2C BUS Control, 4-input, 3-output and Canal Plus Compatible MM1422, 1423, 1442, 1443 Application Circuit |
Price & Availability of MM1422
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |